The integra scanner can be mounted on different media and can be dressed to give it various looks to match own decor. This is accomplished by using various accessories that can be grouped into three categories:
- Mounting options to secure the scanner onto the mounting media
- Decorative cover plates that goes over the scanner
- Wall trim plates that goes around the scanner
Mounting Options
The ekey integra fingerprint scanner has very small footprint and is designed to be mounted in various ways as follows:
 
|
Regardless of the integra scanner mounting options, the recommend mounting height of the integra scanner is 62 inches. |
Back To Top >>
No Bracket - Flush Mount without Bracket
 
|
The integra fingerprint scanner can be mounted directly on the door or similar media without requiring any bracket. Mounting the integra scanner without bracket requires preparation of an opening that measures approximately W1½ x H3¼ x D ½ for seating the scanner. click here to view the integra scanner exact measurements in a new window |
Securing the integra scanner is accomplished by driving two screws through two preset opening is the body of the scanner. The two screws are hidden behind the decorative cover plate.
When the integra scanner is mounted directly on the door, the usage of electrified hinges or similar solution should be considered for the transfer of power and signal between the door and surrounding wall.
Integra scanner dimensions Picture Mounting instructionsBack To Top >>
Cut-in Bracket - Flush Mount Retrofit Bracket(drywall)
 
|
The cut-in drywall bracket (Part Number 403521) is suitable for mounting the integra scanner on already installed and finished drywall. |
The integra cut-in drywall bracket requires wall opening that measures W 1¾ x H 3¾x D 4 inches for seating the scanner. The bracket is secured to the wall by a back brace that is tighten with a screw.
Securing the integra scanner is accomplished by driving two screws through two preset opening is the body of the scanner. The two screws are hidden behind the decorative cover plate.
Back To Top >>
Rough-in Bracket - Flush Mount Rough-in bracket (new Construction)
 
|
The integra rough-in bracket (Part Number 403522) is suitable for preparing during the rough-in stage of new constructions of drywall, stucco, or brick walls. |
Nails or screws are used to secure the bracket to the stud or the wall. The rough-in bracket designed to center vertically the integra scanner on the wall above a 1 gang, or 2 gang box. The rough-in bracket is designed to provide 7/8" collar for stucco, or 5/8" collar for drywall.
Securing the integra scanner is accomplished by driving two screws through two preset opening is the body of the scanner. The two screws are hidden behind the decorative cover plate.
Back To Top >>
In a Box - integra Box Surface Mount (Large Trim)
  |
The Surface-mount box (Part Number 403523) for the integra scanner is suitable in situation where wall opening is not possible. The box measures approximately W4-3¾ x H6-3¾ x D1¾ inches and requires special large metal trim that seat the scanner and seal top of the box. |
Securing the integra scanner is accomplished by driving two screws through two preset opening is the body of the scanner. The two screws are hidden behind the decorative cover plate.
Back To Top >>
Decorative Cover Plates Options
 
|
The integra fingerprint scanner has 3 standard decorative plate color options: Brushed Stainless, White, and Golden. It is used to dress up the integra fingerprint scanner by giving it different look. |
The decorative cover plate (Part number 100415-Brushed Stainless; 100416-White; & 100417-Golden) is made from steel coated with the different color. It is mounted over the scanner by snapping small notches at the top and bottom of the scanner surface.
Back To Top >>
integra Wall Trims Plates Options
The integra fingerprint scanner does not fit standard single gang box or wall plates. It requires special cut trim plate that goes around the scanner. There are two design options:
- Integra Wall Plate - Special Single-Gang
- Integra Metal Plate - Large
Back To Top >>
Single Gang integra Wall Trims Plate
The integra trim plate dress up the integra fingerprint scanner to look like and match light switch on the wall.
These plates are single-gang Screwless Decora Wall Plate with special cut to fit the integra fingerprint scanner.
The integra trim plates are available in five standard colors as follows
 
|
|
Back To Top >>
Large Size integra Wall Trims Plate
|
The special cut metal trim plate measures approximately H6½ x W4½ inches and available in two finishes
|
Back To Top >>
Part Numbers
The following accessories and options are used with the integra scanner only
| Part Number | Color / Finish | Part Name |
| 100415 | Brushed Steel | Integra Decor Element (Brushed Steel) |
| 100416 | White | Integra Decor Element (White) |
| 100417 | Golden | Integra Decor Element (Golden) |
| 403521 | Coated Metal | integra Cut-in Ring for Drywall (Coated Metal) |
| 403522 | Coated Metal | integra Rough-in Bracket for new construction (Coated Metal) |
| 403523 | Coated Metal | integra Box Surface Mount requires large trim (Coated Metal) |
| 403550 | Almond Decora | Screwless Trim - decora wall plate (Almond Decora) |
| 403551 | Black Decora | Screwless Trim - decora wall plate (Black Decora) |
| 403552 | Brown Decora | Screwless Trim - decora wall plate (Brown Decora) |
| 403553 | Ivory Decora | Screwless Trim - decora wall plate (Ivory Decora) |
| 403554 | White Decora | Screwless Trim - decora wall plate (White Decora) |
| 403560 | Stainless Steel | integra Large Metal Trim Ring (Stainless Steel) |
| 800667 | - | integra RJ45 Short Body Plug |
| 100507 | - | integra Control Unit RJ45-CP35 |
| 100526 | - | integra Control Unit Open CP35 Cable |
